MG
Moderator
Please see T-SB-0116-20 Revision 2 (Link Needed)
Introduction:
Some 2018 – 2020 model year Camry and Camry Hybrid vehicles may exhibit the weatherstrip on the panoramic roof center glass peeling on the edges of the glass. Follow the Repair Procedure in this bulletin to address this condition.
REVISION NOTICE:
April 13, 2022 Rev2: • Applicability has been updated to include 2022 model year Camry and Camry Hybrid vehicles.
September 16, 2021 Rev1: • Applicability has been updated to include 2021 model year Camry and Camry Hybrid vehicles. Any previous printed versions of this bulletin should be discarded.
APPLICABLE WARRANTY:
This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle’s in-service date.
Warranty application is limited to occurrence of the specified condition described in this bulletin.
Repair Procedure:
1. Confirm the condition exists. Does the vehicle exhibit the weatherstrip on the panoramic roof center glass peeling on the edges of the glass?
YES — Continue to step 2.
NO — This bulletin does NOT apply. Continue diagnosis using the applicable Repair Manual.
2. Place tape on the glass near the left-hand side AND right-hand side corners to avoid scratching the glass (at least one-fourth the width of the glass). The left-hand side corner is shown, repeat the process for the right-hand side.
3. Remove the existing weatherstrip.
4. Clean the rims using 180-grit sandpaper.
5. Clean the rim with isopropyl alcohol until the surface is smooth and black
6. Apply 3M 94 Primer and let it dry for AT LEAST 90 seconds. Make sure the shine is gone BEFORE proceeding.
7. Line up the ends of the weatherstrip to the edges and make sure both ends align properly
8. Press the mechanical lock on the ridges on both ends as shown.
9. Once the edges are secured, engage the center of the weatherstrip and continue toward the ends. Verify the entire length of the weatherstrip is engaged in the mechanical lock.
10. Remove the cover tape on the ends of the weatherstrip and push the ends onto the rims on both sides. Press firmly on the rim area of the weatherstrip to ensure proper adhesion. Hold and press firmly for five to seven seconds.
11. AFTER the repair is complete, allow the adhesive to cure for AT LEAST 24 hours.
Introduction:
Some 2018 – 2020 model year Camry and Camry Hybrid vehicles may exhibit the weatherstrip on the panoramic roof center glass peeling on the edges of the glass. Follow the Repair Procedure in this bulletin to address this condition.
REVISION NOTICE:
April 13, 2022 Rev2: • Applicability has been updated to include 2022 model year Camry and Camry Hybrid vehicles.
September 16, 2021 Rev1: • Applicability has been updated to include 2021 model year Camry and Camry Hybrid vehicles. Any previous printed versions of this bulletin should be discarded.
APPLICABLE WARRANTY:
This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle’s in-service date.
Warranty application is limited to occurrence of the specified condition described in this bulletin.
Repair Procedure:
1. Confirm the condition exists. Does the vehicle exhibit the weatherstrip on the panoramic roof center glass peeling on the edges of the glass?
YES — Continue to step 2.
NO — This bulletin does NOT apply. Continue diagnosis using the applicable Repair Manual.
2. Place tape on the glass near the left-hand side AND right-hand side corners to avoid scratching the glass (at least one-fourth the width of the glass). The left-hand side corner is shown, repeat the process for the right-hand side.
3. Remove the existing weatherstrip.
4. Clean the rims using 180-grit sandpaper.
5. Clean the rim with isopropyl alcohol until the surface is smooth and black
6. Apply 3M 94 Primer and let it dry for AT LEAST 90 seconds. Make sure the shine is gone BEFORE proceeding.
7. Line up the ends of the weatherstrip to the edges and make sure both ends align properly
8. Press the mechanical lock on the ridges on both ends as shown.
9. Once the edges are secured, engage the center of the weatherstrip and continue toward the ends. Verify the entire length of the weatherstrip is engaged in the mechanical lock.
10. Remove the cover tape on the ends of the weatherstrip and push the ends onto the rims on both sides. Press firmly on the rim area of the weatherstrip to ensure proper adhesion. Hold and press firmly for five to seven seconds.
11. AFTER the repair is complete, allow the adhesive to cure for AT LEAST 24 hours.